IDRAC 6 Problem
I have a server Dell Power Edge R610 I am setting up. I can log into the IDRAC web page, root + password (admin) but every page under System is listed as undefined, and every tab says The webpage...
View ArticleDell OME will connect to only some domain servers
I am new to Dell OME. Just installed it (version 1.3) several days on a domain server member. All servers in domain are Windows 2008r2 with latest updates and service packs. Discovery by OME found all...
View ArticleDell power edge server as home desktop computer.
I have an old, well second hand Dell power edge 840 server. I'm thinking of repurposing this thing as a home desktop system. so far I installed 3 gigs of off the shelf DDR2 5300 desktop ram, got it...
View ArticleDell VRTX Network Time Protocol not working
Hi,I am trying to setup NTP sync on my Dell VRTX by going to Setup -> Date Time.Here I entered the IP to clock sync server, but It does not update my time.I tried to use the CMC network ethernet...
View ArticleSNMP issue with latest iDRAC 7 software
We recently upgraded the iDRAC software on 2 of our M620 blade servers (BIOS Version 2.2.10 / Firmware Version 1.57.57 (Build 04) / Lifecycle Controller Firmware 1.3.0.850 / IDSDM Firmware Version...
View ArticleIssue with installing ESXi 5.1 server on Dell XPS 8700... [repost from...
So, I just purchased two XPS 8700's to go along with my XPS 8500 that runs ESXi server just fine for my home lab. After trying to install ESXi server on them the first time, the network card was not...
View ArticleiDRAC 7 Enterprise - power control over IPMI via vCenter
HiI have 2 new R720 servers running ESXi 5.0 U3 (same vCenter version). With previous ESXi hosts, I've been able to configure vCenter to issue power-on commands using IPMI. This is configured in...
View ArticleOpenManage Can't Install Server Instrumentation
I'm installing OpenManage Server Administratror across our servers, mixture of different PowerEdge servers and Windows OS's. It's installed and working fine on some but not on others. The issue is with...
View ArticleDRAC firmware update fails, says flash must not be formatted or in use
I am trying to update firware for DRAC in PowerEdge 2950 III, I get error about it need flash drive must be non-formatted and not in use.There is a flash drive showing up as G: i think that's what it...
View ArticleDell R520 Driver Issue
I hope this is the right place. We have a Dell R520 server that was recently installed, win server 2008 r2. When I click on device manager we have perhaps 10-30 items in Other Devices. Most listed as...
View ArticleFrom OMSA to OME+DRM?
I have a small server (PE T300) running SBS 2003 SP2 (32-bit) with OMSA. I've been persuaded that DELL Repository Manager will make my life easier regarding DELL patch and firmware management. I've...
View ArticleAfter Updating via USC, no way to pick NIC
I updated my R720xd using the USC on boot (F10). Usually in network settings, set it for NIC1 using DHCP. Updated all the firmware and lifecycle controller to latest versions. After it was done and all...
View ArticleR420 server no idrac port
Hi all, In the rear of server poweredge R420 , I cannot see idrac port located. what does it mean. I can see in the base configuration if I entered ST, it is mentioned as idrac 7 express. where it is...
View ArticleVirtual Disk bad blocks
Hi,After a disk failure we had a message saying "The Virtual Disk has bad blocks. For more details, see the Virtual Disk Bad Block Management section in the Online Help.". I want to clear them out but...
View ArticleiDRAC7 OpenSSL
Need a solution for this. We are getting scans form our security using Foundstone that even with the latest 1.57.57 iDRAC firmware the systems are showing positive for this vulnerability.I need to...
View ArticleMUMC How to delete inaccessible node?
Hey,I'm using MUMC version 01.08 build 0015 and reached my limit of 32 nodes. Since I'm in the progress of installing ULNM for our branches I need to clear two nodes which couldn't be reached anymore,...
View ArticleInstalling OpenManage on a PowerEdge T610 with Intel Xeon E5504 2.00/4.8...
I had a drive fail on a Raid 5 configured PowerEdge T610. After replacing the drive I wanted to install OpenManage to better monitor the status of this server and downloaded the latest OpenManage...
View ArticleHere is the DELL Document Response for openssl
Here is my attempt to upload the Dell Response to Openssl vulnerability. Hopefully it will load so people can view or download if needed.A couple of calls to technical response and here is what I'm...
View ArticleProblem with autostartup of VMware vCenter (PowerEdge VRTX with 3 x PowerEdge...
I have a problem with autostarting of VMware vCenter Appliance in my setup.Hardware setup:1 x PowerEdge VRTX3 x server modules PowerEdge M520Software setup:3 x ESXi 5.1 running VMware1 x VMware vCenter...
View ArticleAlert from OME
Can anyone tell me what this message means?Device:<servername.domainname> <IP Address> Service Tag:(SVC TAG REMOVED BY MODERATOR), Asset Tag:Unknown, Date:08/18/2014, Time:08:00:42,...
View Article